Showing all 10 results
MASONRY TO STEEL
COLUMN ANCHORS
Weld-on Anchor is designed to anchor masonry to structural steel columns or beams.
AVAILABLE IN: 1/4” dia. x 9”
FINISH: Mill Galvanized
Triangular ties compatible with Type-III anchors.
AVAILABLE IN: Standard dia. size of 3/16″ and lengths of 3″, 4″, 5″, 6″, 7″ & 9″
FINISHES: Hot Dip Galvanized & Special Order Stainless Steel
The anchor ties CMU to vertical steel columns.
AVAILABLE IN: Standard size of 2″ wide x 1/8″ thick x 7″ long with a 1-1/2″ bend (right or left)
FINISH: Mill Galvanized
The corrugated notched column anchor is used to tie masonry to steel columns or beams, with a standard size of 2″ wide, 1/8″ thick, and 7″ long, universal in right or left orientation.
AVAILABLE IN: Standard size of 2″ wide x 1/8″ thick x 7″ long (Universal Rt/Left)
FLANGE SLOT: 5/8″ wide x 1″ deep located 1″ from end
FINISH: Mill Galvanized
The PlateGrip® – Surface Mounted – Bearing Plate Support Tie is a fast and efficient way to hold a surface-mounted embedded plate in place while grouting. It works on all common size CMU.
AVAILABLE IN: Standard sizes of 1/2″ and 5/8” diameter studs, with stud lengths of 4″, 5″, 6″, 7″ & 8″
FINISH: Mill Galvanized
BEAM ANCHORS
Weld-on Anchor is designed to anchor masonry to structural steel columns or beams.
AVAILABLE IN: 1/4” dia. x 9”
FINISH: Mill Galvanized
The Partition Top Anchor (Channel) provides lateral shear resistance at the wall’s upper limit, allowing vertical movement of the slab above without transferring compression loads to the wall below.
AVAILABLE IN: 12-gauge thickness, with options of 6″, 8″, 10″ & 12″, and a standard length of 8″
FINISHES: Hot Dip Galvanized & Special Order Stainless Steel
This anchor is installed by welding the plate to a structural beam or fastening it to a concrete slab with expansion anchors, while the plastic tube is grouted into the CMU cell.
AVAILABLE IN: 12 gauge – 2″ x 3″ plate with 5/16″ dia. holes, a 3/8″ dia. x 7″ long rod, and a PTA tube that fits over the rod
FINISHES: Hot Dip Galvanized & Special Order Stainless Steel
MASONRY TO MASONRY
The Mesh Wall Tie is designed to connect intersecting masonry walls.
AVAILABLE IN: Standard Size 16 gauge – 1/2″ square mesh X 6” X 12”
Additional sizes are available – contact us.
FINISH: Hot Dip
The Z Strap anchor is used for anchoring masonry to masonry for intersecting CMU shear walls.
AVAILABLE IN: Standard Size – 1-1/4” x 1/4” x 2” x 24” x 2”
Other Sizes Available – Call 800-924-6802 or sales@masonaccess.com
FINISHES: Plain (Interior) & Hot Dip Galvanized (Exterior)
CAUTION – Rigid Z-strap anchors are only required at the intersection of structural participating walls. They should not be installed where they are not necessary because the projecting portions of the strap could pose a safety risk during construction.
Wire mesh ties are recommended for use at the intersection of non-participating walls. Click here
AVAILABLE IN FLORIDA ONLY
The L-2 Lintel is a top choice for architectural blocks, offering cost savings, high load capacity, and easy installation. Its lightweight design reduces lifting strain, lowering injury risks and insurance costs, while the simple installation process boosts efficiency and safety. Available in Florida only.