Showing all 23 results
MEMBRANE FLASHING
Mas-n-Flash SA (self-adhering), primerless 40-mil woven coated flashing is a premium, non-asphaltic composite membrane, engineered with a custom-formulated high-content butyl adhesive for superior performance.
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 75 lf rolls | WB Quik Set Sealant |
40-mil thick, non-asphalt composite membrane with a proprietary clear adhesive. This adhesive is factory-laminated to polyethylene sheeting, yielding a flexible membrane that is suitable for application to masonry, concrete, steel, gypsum, wood, and polystyrene (also for use with ICF).
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 75′ rolls | HB Sealant |
Rhino-Bond is a non-asphaltic flashing that maintains flexibility in extreme cold or heat. Rhino-Bond is 40 mils thick consisting of 27 mils of membrane formulated with Dupont’s Elvaloy Kee to add strength, 11 mils of butyl adhesive and 2 mils of release paper.
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 50 lf rolls | WB Quik Set Sealant |
York Seal is a proprietary, self-adhering composite membrane, uniquely combining high strength, low temperature adhesion and high temperature stability into a superior barrier to limit air and moisture transmission.
AVAILABLE IN: 18″, 24″ x 75′ rolls
STAINLESS STEEL MEMBRANE
The York 304 Self-Adhering Stainless Steel Flexible Flashing is designed with a flexible 2 mil sheet of type 304 stainless steel, 8 mils of butyl adhesive, and a siliconized release liner for easy application.
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 50′ & 12″ x 20′ |
York US-100 Sealant |
Bond-N-Flash is a stainless steel composite flashing consisting of 2 mils of stainless steel (type 304) bonded to a permanent clear (PSA) adhesive with a removable silicone coated release liner.
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 75′ rolls | WB Quik Set Sealant |
Mighty-Flash™ SA is a self-adhering stainless steel fabric flashing with a removable release liner for easy application. Its clear adhesive is factory-laminated to a Class A polymeric fabric, with a single sheet of Type 304 or 316 stainless steel bonded to one side. Flexible, puncture- and tear-resistant, it’s designed for long-lasting performance throughout the life of the wall.
| AVAILABLE IN: | SEALANT: |
| 12″, 18″, 24″ x 60′ rolls | HB Sealant |
LAMINATED COPPER FLASHING
Two layers of dense glass fabric and a specially blended asphalt are laminated to a copper core, providing enhanced tensile strength and improved puncture resistance.
Copper weights per square foot are 3oz, 5oz, and 7oz.
| AVAILABLE IN: | SEALANT: |
| 18″, 24″ x 25 lf rolls | WB Flashing Mastic |
DRIP EDGE
Drip Edge Flashing creates an extension beyond the wall plane with a 45° hemmed drip edge. Diverts moisture away from the wall surface below.
AVAILABLE IN: Standard size 26ga x 3″ x 3/8” 45° drip edge x 8′ lengths
Also Available In: 1-1/2″
Custom sizes are available – contact us.
FINISH: Stainless Steel – Type 304
Drip Edge Flashing creates an extension beyond the wall plane with a 45° flat hem. It helps divert moisture to the exterior and also offers a clean architectural line among the flashing course.
AVAILBLE IN: 26ga x 3″ x 3/8” 45° flat hem x 8′ lengths
Custom sizes are available – contact us.
FINISH: Stainless Steel – Type 304
Profiles custom fabricated to fit thru-wall veneer details. Often used in conjunction with self-adhering membrane laminated flashings.
FINISH: Stainless Steel – Type 304
BP-300 is a non-skinning butyl metal flashing sealant formulated to seal laps. It maintains a positive airtight seal by remaining both permanently adhesive and flexible to all substates that it is applied to.
AVAILABLE IN: 10.3 fl oz. tubes
TERMINATION BAR
The Aluminum Termination Bar with Sealant Lip is designed to secure flashing to the backup. The sealant lip creates a channel along the top for sealant.
AVAILABLE SIZE: 14 gauge x 1″ wide x 8’ sealant lip by 10′ sections 5/16″ slotted holes
FINISH: Aluminum
The Stainless Steel Bar with Sealant Lip is engineered to securely fasten flashing to the backup. The sealant lip creates a channel along the top for sealant.
AVAILABLE SIZE: Standard Size – 26ga x 1-1/2″ x 8′ with 5/16″ dia holes
FINISH: Stainless Steel
Securing flashing edge to the wall.
AVAILABLE SIZES:
PVC – 1/8″ X 1″ X 8′ flat w/ 5/16″ dia holes spaced 16” oc.
Stainless Steel – 1/8″ X 1″ X 8′ flat w/ 5/16″ dia holes spaced 16″ oc.
Aluminum – 1/8″ X 1″ X 8′ flat w/ 5/16″ dia holes spaced 16″ oc.
TERM BAR FASTENERS
Self-drilling metal framing screws are designed to attach veneer anchors to steel studs. They feature a corrosion-resistant coating for up to 30 cycles and a silver-grey finish. Compatible with both painted and metal surfaces. They offer long-lasting protection and versatility.
STANDARD SIZES: (w/ Neoprene Washers)
-#10 x 1-1/2″
-#12 x 2″
-#12 x 3″
-#12 x 4″
-1/4″ x 5″
Call on other sizes & finishes!
FINISHES: Polymer Coated and Climaseal
Metal-to-Wood Fasteners
STANDARD SIZE: Standard 9″ x 2″
FINISHES: Polymer Coated w/ Neoprene Washer
Zamac Hammer Screws offer a unique, one-step nail drive anchor with a phillips-type head and screw thread, ideal for use in concrete, block, brick, stone.
STANDARD SIZE: Standard 1/4″ diameter x 1-1/4″ long
Other lengths available – contact us.
FINISHES: Zamac Alloy body with Carbon Steel Drive Screw & Special Order Stainless Steel